免费看黄在线_狠狠干狠狠干_成人黄色在线观看视频_少萝裸体视频_乱子伦一区二区_欧美阿姨_西西毛片_国产成人精品一区二区三区视频_空姐一级片_日韩精品高清在线_1000又爽又黄禁片_黄页视频网站_亚洲女人久久久_麻豆网站在线_亚洲第四页

Trap name: color difference

cause: 

1. The coating film thickness is not uniform;

2. The temperature distribution of the curing furnace is not uniform;

3. The workpieces of different materials, thicknesses, shapes and sizes are simultaneously produced and operated;

4. When replacing the color of the paint, if the powder supply device, spray gun, dusting chamber and powder coating are not cleaned;

5. Chromatic aberration caused by uneven distribution of powder pigments.

Solution:

1. Ensure that the film thickness is uniform;

2. The temperature distribution of the curing furnace is uniform;

3. It should be classified according to the material, thickness, shape and size of the workpiece, and then set different baking time for baking and curing, which may reduce the color difference of the coating film;

4. When replacing the paint, clean the parts and try to stagger the materials with different color difference.

5. Improve the quality of the powder to ensure that the L, a, b of the powder are not much different and positive and negative.

Defect name: loss of light, yellowing

cause:

1. The pigment of the powder coating itself is not resistant to high temperature or the high temperature of the resin material is easy to turn yellow;

2. The quality of the pre-treatment of the workpiece is poor and there are residues;

3. The curing time is too long or the curing temperature is too high, the local temperature is too high or too close to the heating tube;

4. Two different color or nature powders are mixed.

Solution:

1. Use high quality powder coating;

2. Wipe clean before pre-treatment, clean the debris before painting;

3. Select the appropriate curing temperature and time, the curing furnace increases the hot air circulation to ensure the proper distance between the workpiece and the heat source;

4. Thoroughly clean the powder supply tank, recovery system, powder feeding pipe, spray gun, spray chamber and other devices when changing the powder.

Defect name: impurities, particles

cause:

1. Curing impurities in the furnace;

2. Dust in the dusting room, clothing fibers, equipment abrasive grains and dusting system;

3. Excessive powder additives, uneven pigment dispersion or too high temperature during powder production, some of the powder has been cross-linked and cured;

4. The powder coating is agglomerated and agglomerated, and the atomization is not good when it is sprayed;

5. There are particles and impurities on the surface before the profile is sprayed;

6. Too much recycled powder is added and not sieved;

7. The coating is sprayed too thin, and the substrate is difficult to cover with mild disease.

Solution:

1. Thoroughly clean the inner wall of the curing oven with a damp cloth and a vacuum cleaner, focusing on the gap between the suspension chain and the duct;

2. Purge the dusting system with air before starting work every day, thoroughly clean the powder spraying equipment and the powder spraying room with a damp cloth and a vacuum cleaner;

3. Improve the quality of the powder;

4. Change the conditions of the warehouse, and use the expired plastic powder to transform the painting equipment;

5. Clean up before spraying, reduce the burrs of the profile, etc.;

6. The recycled powder added is suitable and sieved.

7. Appropriately increase the coating thickness.

Defect name: bubble, shrink hole, pinhole

cause:

1. Pre-treatment degreasing or degreasing after washing to cause surfactant residue;

2. The oil and water content in compressed air exceeds the standard;

3. The water content of the powder coating itself exceeds the standard or the raw material is unqualified, the volatile content exceeds the standard or the powder is damp;

4. The oil stain on the hanging chain will fall into the dusting room or the oven, which will also pollute the powder coating, the powder spraying room and the drying tunnel;

5. Shrinkage caused by mixing powder;

6. The spray gun is too close to the workpiece, causing electric shock perforation.

Solution:

1. Control the concentration of the degreasing tank, reduce the amount of oil in the profile and enhance the washing effect;

2. Increase the oil-water separator to achieve dry compressed air;

3. Use high-quality powder coating or improve powder storage and transportation conditions, increase dehumidifier to ensure timely use of recycled powder;

4. Clean the hanging chain in time to ensure that no oil is dropped;

5. Thoroughly clean the dusting system when changing powder;

6. Use a suitable distance (preferably 150-300mm) for dusting.

Defect name: orange peel is serious

cause:

1. The surface of the workpiece is too rough and the coating is difficult to level;

2. The powder particle size is too coarse or the self-leveling property is poor;

3. The coating is too thin or too thick, when it is too thin, it is muscle-like wrinkles, and when it is too thick, it is marked with orange peel;

4. Electrostatic shielding, the film thickness is not uniform; 5. The curing temperature is too low, not fully leveled.

Solution:

1. The surface is refined by sanding or the like, and the coating is suitably thicker;

2. Use high quality powder coating;

3. Master the powder amount and spraying time to ensure the appropriate thickness (40-60μm);

4. Improve the spray gun, reduce the static shielding area as much as possible or use the friction type spray gun;

5. Increase the curing temperature and extend the leveling time of 110-135 °C for the melt leveling area. This area should be warmed up slowly, and the time is 8-10.

Defect name: poor powder rate

cause:

1. The voltage is too low when spraying;

2. The grounding condition of the workpiece is not good;

3. The high voltage generator resistance is too small and the output current is too large;

4. The dust pressure is too large;

5. Hook insulation, poor conductivity;

6. The spray gun is too far away from the workpiece;

7. Poor powder properties.

Solution:

1. The voltage is adjusted to an appropriate value of 60-90KV;

2. Add ground wire to ensure good grounding;

3. Appropriately increase the resistance of the resistor;

4. Properly reduce the powder supply pressure;

5. Regularly clean the hooks to make the conductivity good;

6. Adjust the gun distance properly;

7. Use high quality powder coating.

Disclaimer: The content of this article is reproduced from the aluminum processing public number. The copyright belongs to the original author. The purpose of the reprint is to convey more information. It does not mean that the public number agrees with its opinions and is responsible for its authenticity. If you are involved in the content, copyright and other issues, please call or write to us, we will deal with it in time!